太赫兹波计算鬼成像:原理和展望

本文立足于太赫兹波成像领域近年来备受关注的研究热点—太赫兹波计算鬼成像,首先回顾了鬼成像从量子到经典再到计算的历史过程,然后阐述了计算鬼成像的数学原理,随后综述了计算鬼成像在太赫兹波段的发展历程,及其在超衍射分辨成像、石墨烯光电导成像、太赫兹光谱成像等方面的应用,并在最后展望了太赫兹波计算鬼成像的发展前景:计算鬼成像作为一种成像手段,可以绕开在太赫兹频段缺乏经济高效的焦面阵列式探测器的难题,但目前的成像帧率还难以满足快速成像的应用需求,相信在未来随着器件性能的提升和成像算法的优化,其成像帧率可以得到大幅提升。     

Halogenation effect promoted low bandgap polymers based on asymmetric isoindigo unit with low energy loss

To optimize the energy levels of the structural framework of isoindigo polymers, a series of asymmetric isoindigo based low bandgap polymers with chlorine, fluorine and thiazole substituents was constructed and their optical, electrochemical and photovoltaic properties were comparatively evaluated for the impact of different substitutions. In comparison with the polymer based on 2,2'‐bithiophene and isoindigo unit (PTi) with non‐substituted bithiophene as the donor moiety, the highest occupied molecular orbital energy level for the newly synthesized polymers is significantly decreased, and in turn an improvement of the open‐circuit voltage (V_OC) is noted in the corresponding photovoltaic devices. More importantly, combined with a low bandgap of 1.32 eV, the energy losses (E_loss) could be reduced to 0.61 eV for polymer based on chlorinated 2,2'‐bithiophene and isoindigo unit (PCl). In addition, the halogen moieties are observed to be superior in device fabrication and give better values than the thiazole substituent. Both fluorinated and chlorinated polymer donors exhibited improved performance compared with the original polymer PTi. Consequently, this work not only presents the influence of different electron withdrawing substituents on the physicochemical and photovoltaic performance, but also backs the concept of how to reduce the energy loss via the heteroatom effect. © 2020 Society of Chemical Industry     

低温绝热气瓶绝热性能检测时间优化分析

蒸发率是用来检测低温绝热气瓶绝热性能是否合格的一个重要指标,但是目前仍存在检测时间较长的不足。依据一维传热模型,提出了一种基于一定检测时长的优化检测方法。该方法以少于24 h的实际检测数据作为样本来获取传热系数等部分参数,并利用获取的参数预测剩余时间的蒸发流量,最终实现缩短检测时间的目的。为了验证优化方法的有效性,搭建了恒温箱实验台并进行了相关试验测试。对比结果表明,计算结果与试验值符合良好,误差在5%以内,验证了模型的可靠性与实用性。     

改良剂对重金属污染根际土壤理化性质影响的研究进展

针对现阶段土壤中重金属污染较为严重的问题及各类修复方法各有利弊的现状,分析了近年来相关学者对于改良剂对重金属污染根际土壤理化性质影响的研究进展,研究了常见有机和无机改良剂对重金属胁迫下根际土壤pH值、氧化还原电位(Eh)、酶活性、化学性质、微生物菌落种群等理化性质的影响以及对重金属的化学沉淀和溶解平衡的影响。后期应加强超富集植物与一般植物根际、非根际理化性质的差异研究;土壤中重金属种类及污染程度与根际土壤理化性质的关系研究;土壤中其他环境因子的影响以及根际土壤中重金属的作用机理方面的研究。     

Stable Organic Titanium Catalysts and Reactive Distillation Used for the Transesterification of Dimethyl Carbonate with Phenol

The transesterification of dimethyl carbonate with phenol to methyl phenyl carbonate (MPC) was investigated on novel catalysts such as titanium diisopropoxide bis(ethyl acetoacetate) and titanium dibutoxide bis(ethyl acetoacetate) in a closed batch reactor at 185–206 °C under high pressure. The produced methanol could be removed efficiently by reactive distillation in order to overcome the equilibrium. The prepared catalysts have higher resistance to water than titanium alkoxides. Phenol conversion as high as 86.4 % with an MPC selectivity of 99.4 % was achieved under optimal reaction conditions within 9 h. Most of the catalytic activity was retained after repeated use for ten times.     

高强不锈钢绞线网与ECC黏结-滑移关系模型

高强不锈钢绞线网与ECC的黏结是二者协同工作的基础，且黏结 滑移关系模型是其黏结性能的综合反映，故通过对17组51个高强不锈钢绞网增强ECC薄板试件进行单边拉拔试验，研究横向钢绞线间距、纵向钢绞线直径和相对锚固长度等因素对钢绞线网在ECC中黏结性能的影响规律。试验结果表明，横向钢绞线的设置可使黏结破坏由脆性破坏转变为延性破坏；高强不锈钢绞线网与ECC的黏结滑移曲线可分为5个阶段，分别为上升段、微降段、延性强化段、下降段和残余段。基于试验结果，对钢绞线网在ECC中的黏结破坏特征和黏结 滑移机理进行分析，在相关黏结-滑移关系模型的基础上，提出钢绞线网与ECC的黏结 滑移关系模型，并进行模型参数分析。所提模型及模型参数计算公式与试验结果吻合良好，能较好地反映钢绞线网与ECC的界面黏结滑移特征。     

孔隙水压对充填体性能的影响

为探究大水矿山充填体的力学性能变化,将充填体试块置入高压水体中使其内部形成孔隙水压,研究孔隙水压下充填体的抗压强度、抗拉强度和含水量等指标的变化。试验以孔隙水压、浸入时间、充填配比和料浆浓度为主要影响因素,开展29组充填体强度试验。方差分析表明,料浆浓度和充填配比对充填体抗压强度影响极显著,孔隙水压影响显著;浸入时间对充填抗拉强度影响显著。相同充填配比和料浆浓度下的充填体抗压和抗拉强度随孔隙水压和浸入时间增长而下降,其中抗拉强度下降幅度较大。充填体含水量随孔隙水压增大而增大,增长趋势和充填体强度增大趋势相吻合。